However, here is another method thatįind the directory "C:\localtexmf\miktex\config", and ( not with a formatted editor such as Word or That is a textfile, whichĬan be edited with a texteditor such as Notepad You will find some of Miktex's configuration settings in the file (This is really a Miktex issue, but it does affect TexnicCenter too.) To go to "Start" "Programs" "Miktex" "Miktex options"Īnd then click on the button that says "Refresh now". The easiest way to update the filename database is You have to update the filename database. I consider those searches to be incredibly helpful, and I've never seen any other DVI previewer that can do both of them.Īny time that you add some files that you want Miktex to be able to find, Click on that line, and you should see something about TEXCNTR.EXE copied automatically into the box that is labeled "Command line." Now click on "OK." To see what this accomplishes, read my discussion of forward and inverse search. You should see, among the options, "TeXnicCenter (autodetected)". Go to "Start" "Programs" "Miktex 2.7" "Previewer" to start up Yap (which stands for "Yet another previewer," but in my opinion this previewer is much better than any other DVI previewer that I've ever seen). I have not tried the spellchecker yet, so I can't tell you if it's very good. (For instance, how to spell your own name, and the name of your most frequent coauthors.) Additional dictionaries are available, as you'll see in the same display as the "Check spelling" box that you just checked. In TxC, go to "Tools" "Options" "Spelling" and check the box labeled "Check spelling while typing." It will complain initially because you don't already have a personal dictionary, and then it will create one that's where you'll be storing words of your own that aren't in the standard dictionary. Next, turn on the spellchecker if you want to use it. Enter the full path of the PostScript-viewer to use: Answer: C:\Program Files\Ghostgum\gsview\gsview32.exe. Your TeX-distribution supports the generation of PostScript-files. (The program might figure this one out for itself, in which case it won't ask you:).Instead you can click on the "browse" button TeX-distribution are located: Answer: C:\Program Files\MiKTeX 2.7\miktex\bin Of directory, where the executables (latex, tex, etc.) of your The first time you run TxC, it will run its Configuration Wizard, to set itself up. However, when I restarted the computer, everything was okay, including TxC.) The following instructions are for TxC version 1b7.50, which installs more easily than earlier versions. (I don't know about your computer, but on mine, TxC installed properly and then the computer crashed. On my computer, it is located at " C:\Program Files\Ghostgum\gsview\gsview32.exe". Where Gsview is installed on your computer you'll need that information in a few minutes. Next, I would recommend that you install Ghostscript (first) and Gsview (second). If that is not the case on your computer, figure out what is the correct answer, so that you'll be prepared for the questions below. In particular, most of its executables are in the directoryĬ:\Program Files\MiKTeX 2.7\miktex\bin. If you're using a recent installation, you'll probably find all its files in the directory C:\Program Files\MiKTeX 2.7 and its various subdirectories. Then check where its files have been installed. "A4" paper is the size used in much of Europe, size 210 × 297 mm.) (In case you don't know the terminology, here it is: "Letter" size is the paper used in the USA, size 8.5 by 14 inches. You can always change that later, but it will be easier for you if you get it right the first time. It will ask you whether you use Letter or A4 paper for your printing. Miktex and TeXnicCenter (hereafter abbreviated TxC) were designed by different people, but normally they interact together pretty well.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |